[vc_row][vc_column width=”2/3″][vc_column_text]

Victron MultiPlus Inverter ChargerVictron MultPlus

Multi-functional, with intelligent power management

The Victron MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the Victron MultiPlus has several advanced features, as outlined below.

Two AC Outputs

The main output has no-break functionality. The Victron MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the Victron MultiPlus. Loads that should not discharge the battery, like a water heater for example, can be connected to this output (second output available on models with 50A transfer switch only).

Virtually unlimited power thanks to parallel operation

Up to 6 Multi’s can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity.

Three phase capability

In addition to parallel connection, three units of the same model can be configured for three-phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps chargering capacity.

PowerControl – Dealing with limited generator, shore side or grid power

The Victron MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10A per 5kVA Multi at 230VAC). With the Multi Control Panel a maximum generator or shore current can be set. The Victron MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

PowerAssist – Boosting the capacity of shore or generator power

This feature takes the principle of PowerControl to a further dimension. It allows the Victron MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the Victron MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Four stage adaptive charger and dual bank battery charging

The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a forth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the Victron MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery (trickle charge output available on 12V and 24V models only).

System configuring has never been easier

After installation, the Victron MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a new DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features.[/vc_column_text][/vc_column][vc_column width=”1/3″]

Product Enquiries

Product Name

Your Name

Your Email

Subject

Your Message

[/vc_column][/vc_row][vc_row][vc_column width=”1/3″][vc_column_text]

PowerAssist with 2x MultiPlus in parallel

PowerAssist with 2x MultiPlus in parallel

[/vc_column_text][/vc_column][vc_column width=”1/3″][vc_column_text]

Five parallel units: output power 25 kVA

Five parallel units: output power 25 kVA

[/vc_column_text][/vc_column][vc_column width=”1/3″][/vc_column][/vc_row][vc_row][vc_column width=”1/1″][vc_column_text]

12 Volt C 12/800/35 C 12/1200/50 C 12/1600/70 C 12/2000/80 12/3000/120
MultiPlus 24 Volt C 24/ 800/16 C 24/1200/25 C 24/1600/40 C 24/2000/50 24/3000/70 24/5000/120
48 Volt 48/3000/35 48/5000/70
PowerControl Yes Yes Yes Yes Yes Yes
PowerAssist No Yes Yes Yes Yes Yes
Transfer switch (A) 16 16 16 30 16 or 50 50
Parallel and 3-phase operation No No No No Yes Yes
Inverter
Input voltage range (V DC) 9,5 – 17 V 19 – 33 V 38 – 66 V
Output Output voltage: 230 VAC ± 2% Frequency: 50 Hz ± 0,1% (1)
Cont. output power at 25 °C (VA) (3) 800 1200 1600 2000 3000 5000
Cont. output power at 25 °C (W) 700 1000 1300 1600 2500 4500
Cont. output power at 40 °C (W) 650 900 1200 1450 2200 4000
Peak power (W) 1600 2400 3000 4000 6000 10.000
Maximum efficiency (%) 92 / 94 93 / 94 93 / 94 93 / 94 93 / 94 / 95 94 / 95
Zero-load power (W) 8 / 10 8 / 10 8 / 10 9 / 11 15 / 15 / 16 25 / 25
Zero load power in AES mode (W) 5 / 8 5 / 8 5 / 8 7 / 9 10 / 10 / 12 20 / 20
Zero load power in Search mode (W) 2 / 3 2 / 3 2 / 3 3 / 4 4 / 5 / 5 5 / 6
Charger
AC Input Input voltage range: 187-265 VAC Input frequency: 45 – 65 Hz Power factor: 1
Charge voltage ‘absorption’ (V DC) 14,4 / 28,8 / 57,6
Charge voltage ‘float’ (V DC) 13,8 / 27,6 / 55,2
Storage mode (V DC) 13,2 / 26,4 / 52,8
Charge current house battery (A) (4) 35 / 16 50 / 25 70 / 40 80 / 50 120 / 70 / 35 120 / 70
Charge current starter battery (A) 4 (12V and 24V models only)
Battery temperature sensor yes
General
Auxiliary output (A) (5) n.a. n.a. n.a. n.a. Yes (25A) Yes (25A)
Programmable relay or relay driver (6) relay driver (7) relay relay relay driver (7) relay relay
Protection (2) a – g
VE.Bus communication port For parallel and three phase operation, remote monitoring and system integration
Common Characteristics Operating temp. range: -20 to +50°C (fan assisted cooling) Humidity (non condensing) : max 95%
Enclosure
Common Characteristics Material & Colour: aluminium (blue RAL 5012) Protection category: IP 21
Battery-connection battery cables of 1.5 meter M8 bolts Four M8 bolts (2 plus and 2 minus connections)
230 V AC-connection G-ST18i connector Spring-clamp Screw terminals 13 mm2 (6 AWG)
Weight (kg) 10 10 10 12 18 30
Dimensions (hxwxd in mm) 375x214x110 520x255x125 362x258x218 444x328x240
Standards
Safety EN 60335-1, EN 60335-2-29
Emission, Immunity EN55014-1, EN 55014-2, EN 61000-3-3
Automotive Directive 2004/104/EC

[/vc_column_text][/vc_column][/vc_row]